Error code · Dryer

Kenmore 110 VMAX Dryer Code F1 E1 (110 / Whirlpool-built VMAX): the control wants service

A Kenmore VMAX or electronic-control dryer with a 110 prefix, built by Whirlpool, alternates an F and an E in the display to say the control has detected a problem that needs service. For F1 E1,…

Medium · inspection needed

(713) 955-7152

Code: F1 E1 (110 / Whirlpool-built VMAX)
Appliance: Dryer
Brand: Kenmore
Warranty: 30-day workmanship

What F1 E1 (110 / Whirlpool-built VMAX) means

A Kenmore VMAX or electronic-control dryer with a 110 prefix, built by Whirlpool, alternates an F and an E in the display to say the control has detected a problem that needs service. For F1 E1, Whirlpool's page gives only a power-cycle procedure and no meaning, so we cannot say which circuit it concerns. The owner sees F1 and E1 take turns and the dryer may not start. An older description of a motor relay cannot be traced to a document.

Common causes of F1 E1 (110 / Whirlpool-built VMAX)

Main control board
Control wiring and connectors
Power glitch that set the code
Meaning of F1 E1 itself, which we confirm in person

✓ One safe check you can try

1. Switch the dryer's circuit breaker off and wait a full sixty seconds before switching it on again. 2. Clean the lint screen and make sure the door closes fully. 3. Start a Timed Dry cycle and stay nearby for the first minute. 4. Note whether F1 and E1 alternate again. 5. If they do, leave the dryer alone and call us.

! Why to stop there

No meaning for F1 E1 is documented, so we avoid guessing a failed part.
We test the control and its wiring on site.
The price is written before the work, and our 30-day warranty applies.

Opening a panel yourself does not automatically cancel a manufacturer warranty, but it can cause accidental damage, and some manufacturers set their own service conditions. Check your warranty terms, or ask us, before deciding.

→Same appliance

Other Dryer codes

L2Kenmore 110 Dryer Code L2: Low or No Line Voltage nP / gASKenmore Elite 796 Dryer Code nP / gAS: Power Cord and House Supply PFKenmore 110 Dryer Code PF: power was lost mid-cycle PS / tE4 / Add Water (796 / LG-built steam)Kenmore Elite 796 Steam Dryer Code PS / tE4 / Add Water (796 / LG-built steam): Supply and Sensor tE1 / tE2 (796 / LG-built)Kenmore Elite 796 Dryer Code tE1 / tE2 (796 / LG-built): Temperature Sensor F4 E1 / F4 E2 (110 / Whirlpool-built VMAX)Kenmore 110 VMAX Dryer Code F4 E1 / F4 E2 (110 / Whirlpool-built VMAX): Heater System F4 E3 (110 / Whirlpool-built VMAX)Kenmore 110 VMAX Dryer Code F4 E3 (110 / Whirlpool-built VMAX): vent or lint screen restricted F4 E4 (110 / Whirlpool-built VMAX)Kenmore 110 VMAX Dryer Code F4 E4 (110 / Whirlpool-built VMAX): Low Line Voltage

F1 E1 (110 / Whirlpool-built VMAX)F1 E1 (110 / Whirlpool-built VMAX) questions

What is my dryer telling me with F1 E1?

It means the control found a problem that needs service. The exact circuit is not documented for this 110-series, Whirlpool-built platform, so we do not claim a specific failed part.

Will turning the breaker off help?

It can clear a one-time glitch. If the code comes back after the Timed Dry test, stop using the dryer and call us so the control can be tested properly.

Is the motor relay the cause?

We have seen that claim, but it cannot be traced to any document we can verify. We test the control and wiring on site before we name a part.

Book a visit

Still seeing F1 E1 (110 / Whirlpool-built VMAX)?

A technician diagnoses it on site and gives you the price in writing before any work starts.

(713) 955-7152